manualshive.com logo in svg

IBM TotalStorage DS300, Best Practices Manual, Page: 25 / 680

Share
Download
IBM TotalStorage DS300 Best Practices Manual Download Page 25

 Chapter 1. Storage Area Networks (SAN) overview 

7

Figure 1-2   SAN versus NAS

1.4  SAN components

Fibre Channel is the predominant architecture upon which most SAN 
implementations are built, with FICON® as the standard protocol for z/OS® 
systems, and FCP as the standard protocol for open systems. The SAN 
components described in the following sections are Fibre Channel-based, and 
are shown in Figure 1-3 on page 8.

Server

Storage

LAN

SAN

Servers

Clients

Storage

LAN

Clients

NAS 
File Server
Appliance

Traditional Storage Direct Attached

Storage Area Network

Network Attached Storage

Summary of Contents for TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments