manualshive.com logo in svg

IBM TotalStorage DS300, Best Practices Manual, Page: 202 / 680

Share
Download
IBM TotalStorage DS300 Best Practices Manual Download Page 202

184

 

IBM TotalStorage DS300 and DS400 Best Practices Guide

Figure 4-167   Hyperterminal — Send file 

7. The firmware file will be transferred to the controller. This dialog will close 

after successful transmission or because to many errors.

Figure 4-168   Hyperterminal — transfer firmware data 

8. After the firmware file was successful transferred the command line interface 

informs about the next steps. The firmware is written to the controller.

Figure 4-169   Command line interface — successful image flash

 27302294 bytes read...
RedBoot already at version 05.05.05, skipping...
Writing kernel
Writing filesystem
  27302294 bytes read...
Image successfully uploaded.

Use the 'system reboot' command to run this new firmware image

DS300-1[A]#

Summary of Contents for TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments