IBM TotalStorage DS300 Best Practices Manual Download Page 434

Page: 434 / 680

416

IBM TotalStorage DS300 and DS400 Best Practices Guide

Figure 7-304 Microsoft iSCSI software initiator 2.0 configuration step 24

25.To ensure that the drives are available on startup they have to be persistently

bound. This is done in the

Bound Volumes/Devices

tab in the iSCSI initiator

properties dialog. Click

Add

to bind a volume.

Summary of Contents for TotalStorage DS300








































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TotalStorage DS300

Reviews:

IBM TotalStorage DS300, Best Practices Manual, Page: 434 / 680

Search results

Summary of Contents for TotalStorage DS300

Reviews: