manualshive.com logo in svg

IBM TotalStorage DS300, Best Practices Manual, Page: 325 / 680

Share
Download
IBM TotalStorage DS300 Best Practices Manual Download Page 325

 Chapter 7. TotalStorage DS300 installation 

307

5. You can specify a installation destination. Click 

Next

 to continue.

Figure 7-128   SANsurfer Linux installation step 5

6. Click 

Install

 in the pre-installation summary to start the installation.

Figure 7-129   SANsurfer Linux installation step 6

7. Click 

Done

 to close the installation application.

Summary of Contents for TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments