Home
/
IBM
/
TotalStorage DS300
/
Best Practices Manual

IBM TotalStorage DS300, Best Practices Manual, Page: 277 / 680

Share

Page: 277 / 680

IBM TotalStorage DS300 Best Practices Manual Download Page 277

Chapter 7. TotalStorage DS300 installation

259

7.1.9 Use SANsurfer and verify current configuration

The installation of the SANsurfer utility is complete. On the desktop is now a
SANsurfer icon. Use this icon to start SANsurfer and check the current HBA
configuration.

1. After SANsurfer has started an empty window is shown. Depending on the

chosen option during installation the left site of the window may have less
tabs than shown below. SANsurfer will look like the figure below when all
agents and GUIs are installed. Select the

iSCSI HBA

tab.

Figure 7-51 SANsurfer

2. Click

Host

→

Connect

.

Figure 7-52 SANsurfer — Host

→

connect

3. Localhost is chosen by default. An IP address of a remote system where the

agent is installed can be specified here as well. Click

Connect

.

«
...
275
276
277
278
279
...
»

Summary of Contents for TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments