manualshive.com logo in svg

IBM TotalStorage DS300, Best Practices Manual, Page: 311 / 680

Share
Download
IBM TotalStorage DS300 Best Practices Manual Download Page 311

 Chapter 7. TotalStorage DS300 installation 

293

Figure 7-103   iSCSI HBA and host information 

4. Select in HBA list a HBA and verify that firmware and BIOS level is up to date.

Figure 7-104   HBA information 

5. Select the register card HBA Options when you have to perform a BIOS or 

firmware update. Buttons for updating the firmware and the BIOS are 
available.

Summary of Contents for TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments