Home
/
IBM
/
TotalStorage DS300
/
Best Practices Manual

IBM TotalStorage DS300, Best Practices Manual, Page: 211 / 680

Share

Page: 211 / 680

IBM TotalStorage DS300 Best Practices Manual Download Page 211

Chapter 4. TotalStorage DS300 and DS400 management

193

Installable Edition, needs to be installed first before it can be used. A start menu
entry is created to run the utility. For more details about DSA and the download
see the URL below. This book assumes that the DSA Portable Edition is used.

Link of DSA:

http://www-1.ibm.com/servers/eserver/xseries/systems_management/dsa.html

DSA can be executed with options. The order of the options are important. First
are all options for the installer specified. To use options for the DSA itself, specify
/a followed by those options. A few important options are:

/s

accept the license, option is for the installer

/a

option for the installer to pass all remaining options to DSA

/v

DSA option to create HTML output files

More about the options are documented in the readme file of DSA which can be
downloaded together with the appropriate DSA edition.

Download the DSA portable edition and store the file on all systems attached to
the IBM TotalStorage DS300 and IBM TotalStorage DS300. Perform the following
steps to gather information about the system:

1. Click Start

→

Run. In the Run window select the DSA executable.

Figure 4-185 Run — DSA installer

2. Add the option /a /v behind the executable. then click

OK

.

«
...
209
210
211
212
213
...
»

Summary of Contents for TotalStorage DS300









































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments