IBM 2109 - SAN Fibre Channel Switch Model S16 Service Manual Download Page 38

Page: 38 / 178

Step 1. Mounting the moving slide and locking ears to the switch

1. Locate and disassemble the slides by fully extending the slide, pressing the

release as shown in Figure 7, and pulling the slide apart.

2. Mount the moving portion of the slide and the locking ears to the switch as

shown in Figure 8. Use the screws provided with the locking ears. Mount the
slide portion first, and then the locking ears.

Step 2. Mounting the fixed portion of the slide in the rack

1. Open the rack-mounting brackets kit and mount the brackets to the wider fixed

portion of the four slides. One bracket mounts to each end of the fixed portion
of the slides as shown in Figure 9 on page 23.

SJ000046

Figure 7. Moving slide

SJ000047

Front

Figure 8. Mounting the moving portion of slide and locking ears to the switch

IBM SAN Fibre Channel Switch: 2109 Model S16 Installation and Service Guide

Summary of Contents for 2109 - SAN Fibre Channel Switch Model S16



















































































































































































Search results

Summary of Contents for 2109 - SAN Fibre Channel Switch Model S16

Reviews:

Related manuals for 2109 - SAN Fibre Channel Switch Model S16

Brands by name

Popular brands

IBM 2109 - SAN Fibre Channel Switch Model S16, Service Manual

Search results

Summary of Contents for 2109 - SAN Fibre Channel Switch Model S16

Reviews:

Related manuals for 2109 - SAN Fibre Channel Switch Model S16

Brands by name

Popular brands