![background image](http://html1.mh-extra.com/html/ibm/2109-san-fibre-channel-switch-model-s16/2109-san-fibre-channel-switch-model-s16_service-manual_3369045138.webp)
Table 40. Action codes and recommended actions (continued)
Action
code
Recommended action
4
Replace the power supply. See “Replacing the power supply” on page 45.
Diagnostic error messages
This section provides information on the probable cause of a diagnostic error and
what actions to take.
Table 41. Diagnostic error messages
Message
Failing test
Description
Probable cause
Action
DIAG-BADINT
Err#1030
Err#2030
centralMemoryTest
cmiTest
The port received an interrupt
when not expecting one.
ASIC failure
1
DIAG-
BUS_TIMEOUT
Err#0B0F
Err#4040F
portRegTest
sramRetentionTest
The ASIC register or ASIC SRAM
did not respond to an ASIC data
access.
ASIC failure
1
DIAG-CAMINIT
Err#223B
CamTest
The port failed to initialize due to
one of the following reasons:
v
Switch is not disabled
v
Diagnostic queue absent
v
Malloc failed
v
Chip is not present
v
Port is not in loopback mode
v
Port is not active
Software operational
setup error or main
boad failure
Retry,
restart or
replace the
mainboard
assembly
DIAG-CAMSID
Err#223C
camTest
The ASIC failed SID NO
translation test.
ASIC failure
1
DIAG-CLEAR_ERR
Err#0001
The port’s diag error flag (OK or
BAD) is cleared.
Informational only
None
required
DIAG-CMBISRF
Err#1021
centralMemoryTest
The central memory SRAMs of
the ASIC did not complete the
BISR within the timeout period.
ASIC failure
1
DIAG-CMBISRTO
Err#1020
centralMemoryTest
The central memory SRAMs of
the ASIC did not complete the
BISR within the timeout period.
ASIC failure
1
DIAG-CMERRPTN
Err#102B
centralMemoryTest
An error was detected at the
wrong port.
ASIC failure
DIAG-CMERRTYPE
Err#102A
centralMemoryTest
The port got the wrong CMEM
error type.
ASIC failure
1
DIAG-CMICKSUM
Err#2036
cmiTest
The CMI message received failed
the bad checksum test.
ASIC or system board
failure
1
DIAG-CMIDATA
Err#2035
cmiTest
The CMI data received did not
match the data transmitted.
ASIC or system board
failure
1
DIAG-CMIINVCAP
Err#2034
cmiTest
An unintended ASIC erroneously
got CMI capture flag.
ASIC or system board
failure
1
DIAG-CMINOCAP
Err#2033
cmiTest
The CMI intended receiver ASIC
failed to get the CMI capture flag.
ASIC or system board
failure
1
122
IBM SAN Fibre Channel Switch: 2109 Model S16 Installation and Service Guide
|
|
|
|
||
|
|
|
|
|
||
|||||
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
||
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
||
|
|
||
|
||
|
|
|
||
|
|
||
|
|
||
|
|
||
|
|
||
|
||
|
|
||
|
||
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
Summary of Contents for 2109 - SAN Fibre Channel Switch Model S16
