Husqvarna TE 250 Owner'S Manual Download

Page: 28 / 169

7 COMBINATION INSTRUMENT

401911-01

–

Wait for 5 seconds.

The combination instrument changes to the next menu

item. The

symbol flashes.

–

Press one of the buttons to select the 24h or 12h display of

the clock.

401912-01

–

Wait for 5 seconds.

The combination instrument changes to the next menu

item. The

symbol flashes.

Resetting the time

–

Press the left button.

The value decreases.

Advancing the time

–

Press the right button.

The value increases.

401913-01

–

Wait for 5 seconds.

The combination instrument changes to the next menu

item. The

symbol flashes.

–

Set the service.

Shortening the service interval

–

Press the left button.

The value decreases.

Extending the service interval

–

Press the right button.

The value increases.

401914-01

Switching off the service interval display

–

Press and hold the left button.

off

appears on the display.

7.5

Setting the kilometers or miles

Info

If the unit is changed, the value

ODO

is retained and converted accordingly.

Condition

The motorcycle is stationary.

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands