Husqvarna TE 250 Owner'S Manual Download

Page: 102 / 169

14 WHEELS, TIRES

100

H03001-10

Main work

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change the rear wheel bearing.

–

Clean and grease shaft seal rings

and contact

surfaces

of the spacers.

Long-life grease (

p. 157)

–

Insert the spacers.

S04844-10

–

Clean and lightly grease the wheel spindle.

Long-life grease (

p. 157)

–

Position rear wheel and insert wheel spindle

The brake linings are correctly positioned.

–

Mount the chain.

S04835-11

–

Position chain adjuster

. Mount nut

, but do not tighten

it yet.

–

Make sure that chain adjusters

are fitted correctly on

adjusting screws

–

Check the chain tension. (

p. 77)

–

Tighten nut

Guideline

Nut, rear wheel spin-

dle

M20x1.5

80 Nm (59 lbf ft)

Info

The wide adjustment range of the chain adjusters

(32 mm (1.26 in)) enables different secondary ratios

with the same chain length.
Chain adjusters

can be turned by 180°.

–

Operate the foot brake lever repeatedly until the brake lin-

ings are in contact with the brake disc and there is a pressure

point.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 55)

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands