Husqvarna TE 250 Owner'S Manual Download

Page: 111 / 169

ELECTRICAL SYSTEM 15

109

S04852-10

–

Take off protection caps

–

Remove faulty main fuse

Info

A faulty fuse has a burned-out fuse wire

A spare fuse

is located in the starter relay.

–

Insert a new main fuse.

Fuse (58011109120) (

p. 150)

–

Check that the electrical system is functioning properly.

Tip

Insert a spare fuse so that it is available if needed.

–

Attach the protection caps

–

Mount starter relay

onto the holder and route the cable.

S04846-12

–

Mount the EFI control unit

on the rubber lugs

Finishing work

–

Mount the seat. (

p. 67)

–

Install the air filter box cover. (

p. 68)

15.5

Changing the fuses of individual electrical power consumers

Info

The fuse box containing the fuses of individual electrical power consumers is located under the seat.

Preparatory work

–

Remove the air filter box cover. (

p. 68)

–

Remove the seat. (

p. 67)

H03747-10

Main work

–

Open fuse box cover

–

Remove the faulty fuse.

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands