Husqvarna TE 250 Owner'S Manual Download | Manualshive

Page: 109 / 169

background image

ELECTRICAL SYSTEM 15

107

Info

Even when there is no load on the 12-V battery, it discharges steadily each day.
The charging level and the method of charging are very important for the service life of the 12-V battery.
Rapid recharging with a high charging current shortens the service life of the battery.
If the charging current or charging voltage are exceeded, the 12-V battery will be destroyed.
If the 12-V battery is depleted by repeated starting, the 12-V battery must be charged immediately.
If the 12-V battery is left in a discharged state for an extended period, it will become deeply discharged

and suffer a loss of capacity, destroying the battery.
The 12-V battery is maintenance-free.

Preparatory work

–

Remove the air filter box cover. (

–

Remove the seat. (

–

Remove the 12-V battery.

H03743-10

Main work

–

Check the battery voltage.
» Battery voltage: < 9 V

–

Do not charge the 12-V battery.

–

Replace the 12-V battery and dispose of the old 12-V

battery properly.

» If the specifications have been met:

Battery voltage:

≥

9 V

–

Charge the 12-V battery.
Guideline

Maximum charging volt-

age

14.4 V

Maximum charging cur-

rent

3.0 A

Maximum charging time

24 h

Recharge the 12-V bat-

tery regularly when the

motorcycle is not being

used

6 months

Battery charger (A54029974000)

This battery charger tests whether the 12-V battery

retains its voltage. It is also impossible to overcharge

the 12-V battery with this battery charger. The charg-

ing time may be longer at low temperatures.
This battery charger is only suitable for lithium iron

phosphate batteries. Observe the accompanying fit-

ting instructions for Husqvarna Motorcycles technical

accessories.

Info

Never remove cover

1

.

–

Switch off the battery charger after charging and disconnect

from the 12-V battery.

Finishing work

–

Install the 12-V battery.

–

Mount the seat. (

«
...
107
108
109
110
111
...
»

Summary of Contents for TE 250










































































































































































Reviews:

No comments

Related manuals for TE 250

Brand: Happy Trails Pages: 4

Brand: hepco & becker Pages: 3

Brand: Memphis Shades Pages: 2

Brand: KTM Pages: 22

Brand: Yamaha Pages: 390

Brand: Yamaha Pages: 468

Brand: Yamaha Pages: 364

Brand: hepco & becker Pages: 4

Brand: Hama Pages: 22

Brand: Bagster Pages: 2

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 100

Brand: Yamaha Pages: 114

Brand: Yamaha Pages: 226

Brand: KTM Power Parts Pages: 7

Brand: Honda Pages: 122

1972 Super Enduro SE-74

Brand: Indian Motorcycle Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands