Husqvarna TE 250 Owner'S Manual Download

Page: 124 / 169

16 COOLING SYSTEM

122

S04264-10

–

Unplug connector

–

Remove coolant temperature sensor

with O-ring and wait

until the coolant escapes without bubbles.

–

Mount and tighten the coolant temperature sensor

with

O-ring.
Guideline

Screw, cylinder head

temperature sensor

M10x1.25

12 Nm (8.9 lbf ft)

–

Plug in connector

–

Mount protection cap

S04265-10

–

Mount radiator cap

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and

death.

–

Always make sure there is sufficient ventilation

when running the engine.

–

Use effective exhaust extraction when starting or

running the engine in an enclosed space.

–

Allow the engine to warm up and cool down again.

–

Check the cooling system for leaks.

–

Check the coolant level. (

p. 118)

Finishing work

–

Install the engine guard. (

p. 85)

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands