Husqvarna TE 250 Owner'S Manual Download

Page: 119 / 169

COOLING SYSTEM 16

117

16.1

Cooling system

H03759-10

Water pump

in the engine ensures forced circulation of the

coolant.
The pressure resulting from the warming of the cooling system is
regulated by a valve in radiator cap

. This ensures that operat-

ing the vehicle at the specified coolant temperature will not result

in a risk of malfunctions.

120 °C (248 °F)

Cooling is effected by the air stream.
The lower the speed, the less the cooling effect. Dirty cooling fins

also reduce the cooling effect.

16.2

Checking the antifreeze and coolant level

Warning

Danger of scalding

During motorcycle operation, the coolant gets very hot and is under pressure.

–

Do not open the radiator, the radiator hoses or other cooling system components if the engine or

the cooling system are at operating temperature.

–

Allow the cooling system and the engine to cool down before you open the radiator, the radiator

hoses or other components of the cooling system.

–

In the event of scalding, rinse the area affected immediately with lukewarm water.

Warning

Danger of poisoning

Coolant is toxic and a health hazard.

–

Keep coolant out of the reach of children.

–

Do not allow coolant to come into contact with the skin, the eyes and clothing.

–

Consult a doctor immediately if coolant is swallowed.

–

Rinse the affected area immediately with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water and consult a doctor immediately if coolant gets into the eyes.

–

Change clothing if coolant spills onto your clothing.

Condition

The engine is cold.

400243-10

–

Stand the motorcycle upright on a horizontal surface.

–

Remove the radiator cap.

–

Check the antifreeze in the coolant.

−

25 …

−

45 °C (

−

13 …

−

49 °F)

» If the antifreeze in the coolant does not match the speci-

fied value:

–

Correct the antifreeze in the coolant.

–

Check the coolant level in the radiator.

Coolant level

above the

radiator fins

10 mm (0.39 in)

» If the coolant level does not match the specified value:

–

Correct the coolant level.

Coolant (

p. 155)

–

Mount the radiator cap.

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands