Husqvarna TE 250 Owner'S Manual Download

Page: 83 / 169

SERVICE WORK ON THE CHASSIS 12

12.37

Checking the frame

S01339-01

–

Check the frame for damage, cracks, and deformation.
» If the frame shows signs of damage, cracks, or deforma-

tion:

–

Change the frame.
Guideline

Repairs on the frame are not permitted.

12.38

Checking the link fork

S01340-01

–

Check the link fork for damage, cracking, and deformation.
» If the link fork exhibits damage, cracking, or deformation:

–

Change the link fork.

Info

Always replace a damaged link fork. Repair of

the link fork is not authorized by Husqvarna

Motorcycles.

12.39

Checking the throttle cable routing

Warning

Danger of accidents

The throttle cable can become kinked, trapped or blocked if it is not routed cor-

rectly.

If the throttle cable is kinked, trapped or blocked, the speed can no longer be controlled.

–

Make sure that the throttle cable routing and the play in throttle cable complies with the specifica-

tion.

Preparatory work

–

Remove the air filter box cover. (

p. 68)

–

Remove the seat. (

p. 67)

–

Remove the right side cover. (

p. 72)

–

Remove the fuel tank.

(

p. 73)

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands