Husqvarna TE 250 Owner'S Manual Download

Page: 42 / 169

9 RIDING INSTRUCTIONS

–

Braking should always be completed before you go into a bend. Change down to a lower gear appropriate

to your road speed.

9.6

Stopping, parking

Warning

Risk of misappropriation

People who act without authorization endanger themselves and others.

–

Do not leave the vehicle unattended if the engine is running.

–

Protect the vehicle against access by unauthorized persons.

Warning

Danger of burns

Some vehicle components become very hot when the vehicle is operated.

–

Do not touch any parts such as the exhaust system, radiator, engine, shock absorber, or brake sys-

tem before the vehicle parts have cooled down.

–

Let the vehicle parts cool down before you perform any work on the vehicle.

Note

Material damage

The vehicle may be damaged by incorrect procedure when parking.

Significant damage may be caused if the vehicle rolls away or falls over.
The components for parking the vehicle are designed only for the weight of the vehicle.

–

Park the vehicle on a firm and level surface.

–

Ensure that nobody sits on the vehicle when the vehicle is parked on a stand.

Note

Fire hazard

Hot vehicle components pose a fire hazard and explosion risk.

–

Do not park the vehicle near to materials which are highly flammable or explosive.

–

Allow the vehicle to cool down before covering it.

–

Apply the brakes on the motorcycle.

–

Shift the transmission into neutral.

(All EU/AR/CN standard models)

–

Press and hold the stop button

while the engine is idling until the engine stops.

(All US standard models)

–

Press and hold the stop button

while the engine is idling until the engine stops.

–

Park the motorcycle on firm ground.

9.7

Transporting

Note

Danger of damage

The parked vehicle can roll away or fall over.

–

Park the vehicle on a firm and level surface.

Note

Fire hazard

Hot vehicle components pose a fire hazard and explosion risk.

–

Do not park the vehicle near to materials which are highly flammable or explosive.

–

Allow the vehicle to cool down before covering it.

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands