Husqvarna TE 250 Page 76 Owner'S Manual Download

Page: 76 / 169

12 SERVICE WORK ON THE CHASSIS

H03705-10

–

Remove screws

(All EU/AR standard models)

–

Hang the horn and horn bracket to one side.

H03704-10

–

Remove screw

with the rubber bushing.

–

Pull the fuel tank breather hose off the fuel tank lid.

H03706-10

–

Pull both spoilers laterally off the radiator and lift off the fuel

tank.

12.31

Installing the fuel tank

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not fuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands