Husqvarna TE 250 Owner'S Manual Download

Page: 121 / 169

COOLING SYSTEM 16

119

Warning

Danger of poisoning

Coolant is toxic and a health hazard.

–

Keep coolant out of the reach of children.

–

Do not allow coolant to come into contact with the skin, the eyes and clothing.

–

Consult a doctor immediately if coolant is swallowed.

–

Rinse the affected area immediately with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water and consult a doctor immediately if coolant gets into the eyes.

–

Change clothing if coolant spills onto your clothing.

Condition

The engine is cold.

Preparatory work

–

Remove the engine guard. (

p. 85)

Main work

–

Position the motorcycle upright.

–

Place an appropriate container under the water pump cover.

H03759-11

–

Remove screw

. Take off radiator cap

–

Completely drain the coolant.

–

Mount and tighten screw

with a new seal ring.

Guideline

Screw, water pump

cover

10 Nm (7.4 lbf ft)

16.5

Refilling with coolant

Warning

Danger of poisoning

Coolant is toxic and a health hazard.

–

Keep coolant out of the reach of children.

–

Do not allow coolant to come into contact with the skin, the eyes and clothing.

–

Consult a doctor immediately if coolant is swallowed.

–

Rinse the affected area immediately with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water and consult a doctor immediately if coolant gets into the eyes.

–

Change clothing if coolant spills onto your clothing.

H03760-10

Main work

–

Make sure that screw

is tightened.

–

Position the motorcycle upright.

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands