Husqvarna TE 250 Owner'S Manual Download

Page: 27 / 169

COMBINATION INSTRUMENT 7

7.1

Overview

402819-10

Overview of indicator lights (

p. 19)

(All EU/AR/CN

standard models)

Overview of indicator lamps (

p. 19)

(All US standard

models)

Left button

Display

Right button

7.2

Activation

402819-01

Activating combination instrument

The combination instrument is activated when one of the buttons

is pressed or an impulse comes from the wheel speed sensor.

7.3

Messages on the combination instrument

401901-01

Possible states

Battery voltage of the combination instrument

–

The

battery voltage of the combination instrument is too

low. Change combination instrument battery.
Service

–

A service is due. Contact an authorized

Husqvarna Motorcycles workshop.

7.4

Adjusting the combination instrument

Condition

The motorcycle is stationary.

401909-01

–

Press both buttons for 3

–

5 seconds.

The Setup menu is displayed. The

UNIT

display flashes.

–

Press one of the buttons to select

UNIT

for the speed in kilo-

meters

KM/H

or miles

M/H

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands