Husqvarna TE 250 Page 97 Owner'S Manual Download

Page: 97 / 169

BRAKE SYSTEM 13

Warning

Danger of accidents

Old brake fluid reduces the braking effect.

–

Make sure that brake fluid for the front and rear brake is changed in accordance with the service

schedule. (Your authorized Husqvarna Motorcycles workshop will be glad to help.)

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

Warning

Danger of accidents

Brake linings which have not been approved alter the braking efficiency.

Not all brake linings are tested and approved for Husqvarna motorcycles. The structure and friction

coefficient of the brake linings, and thus their brake power, may vary greatly from that of original brake

linings.
If brake linings are used that differ from the original equipment, compliance with the original homolo-

gation is not guaranteed. In this case, the vehicle no longer corresponds to its condition at delivery

and the manufacturer warranty shall be void.

–

Only use brake linings approved and recommended by Husqvarna motorcycles.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and brake lines are not

designed for DOT 5 brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid corrodes paint.
Only use clean brake fluid from a sealed container.

S04470-10

–

Stand the vehicle upright.

–

Remove the cable tie on the frame protector.

–

Remove screw cap

with membrane

and the shim.

S04471-10

–

Manually press the brake caliper toward the brake disc to

push back the brake piston. Ensure that brake fluid does not

flow out of the brake fluid reservoir; extract some if neces-

sary.

Info

Make sure that you do not press the brake caliper

against the spokes when pushing back the brake pis-

ton.

–

Remove cotter pin

–

Pull out pin

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands