Husqvarna TE 250 Owner'S Manual Download

Page: 81 / 169

SERVICE WORK ON THE CHASSIS 12

400987-10

–

Pull on the top section of the chain with the specified
weight

Guideline

Weight, chain wear mea-

surement

10 … 15 kg (22 … 33 lb.)

–

Measure distance

of 18 chain rollers in the lower chain

section.

Info

Chain wear is not always even, so you should repeat

this measurement at different chain positions.

Maximum distance

from

18 chain rollers at the

longest chain section

272 mm (10.71 in)

» If distance

is greater than the specified measurement:

–

Change the drivetrain kit.

Info

When a new chain is mounted, the rear

sprocket and engine sprocket should also be

changed.
New chains wear out faster on old, worn

sprockets.

S04837-01

–

Check the chain sliding guard for wear.
» If the lower edge of the chain pins is in line with, or below,

the chain sliding guard:

–

Change the chain sliding guard.

–

Check that the chain sliding guard is firmly seated.
» If the chain sliding guard is loose:

–

Tighten screws on the chain sliding guard.
Guideline

Screw, chain

sliding guard

10 Nm (7.4 lbf ft)

Loctite

243™

Summary of Contents for TE 250










































































































































































Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands

Husqvarna TE 250, Owner'S Manual

Search results

Summary of Contents for TE 250

Reviews:

Related manuals for TE 250

Brands by name

Popular brands