Husqvarna TE 250 Page 85 Owner'S Manual Download | Manualshive

Page: 85 / 169

background image

SERVICE WORK ON THE CHASSIS 12

83

12.41

Adjusting the basic position of the clutch lever

S04405-11

–

Adjust the basic position of the clutch lever to your hand size
by turning adjusting screw

1

.

Info

When the adjusting screw is turned counterclockwise,

the clutch lever moves away from the handlebar.
When the adjusting screw is turned clockwise, the

clutch lever moves closer to the handlebar.
The range of adjustment is limited.
Turn the adjusting screw by hand only, and do not

apply any force.
Do not make any adjustments while riding.

12.42

Checking/correcting the fluid level of hydraulic clutch

Warning

Skin irritation

Brake fluid causes skin irritation.

–

Keep brake fluid out of the reach of children.

–

Wear suitable protective clothing and safety glasses.

–

Do not allow brake fluid to come into contact with the skin, the eyes or clothing.

–

Consult a doctor immediately if brake fluid has been swallowed.

–

Rinse the affected area with plenty of water in the event of contact with the skin.

–

Rinse eyes thoroughly with water immediately and consult a doctor if brake fluid comes into contact

with the eyes.

–

If brake fluid spills on to your clothing, change the clothing.

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

The fluid level rises with increasing wear of the clutch facing discs.
Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and clutch lines are not

designed for DOT 5 brake fluid.
Avoid contact between brake fluid and painted parts. Brake fluid corrodes paint.
Only use clean brake fluid from a sealed container.

S04454-10

–

Move the hydraulic clutch fluid reservoir mounted on the han-

dlebar into a horizontal position.

–

Remove screws

1

.

–

Take off cover

2

with membrane

3

.

–

Check the fluid level.

Fluid level below container

rim

4 mm (0.16 in)

» If the level of the fluid does not meet specifications:

–

Correct the fluid level of the hydraulic clutch.

«
...
83
84
85
86
87
...
»

Summary of Contents for TE 250










































































































































































Reviews:

No comments

Related manuals for TE 250

Brand: Sachs Bikes Pages: 83

Brand: Honda Pages: 393

Brand: klicbag Pages: 2

Brand: KTM Pages: 90

Brand: kellermann Pages: 5

Brand: GAS GAS Pages: 52

TXT RACING 2015

Brand: GAS GAS Pages: 59

Brand: GAS GAS Pages: 56

Brand: GAS GAS Pages: 128

Brand: GAS GAS Pages: 131

Brand: MSA Pages: 168

Brand: Britannia Pages: 9

Brand: Shark Pages: 24

Brand: Vanucci Pages: 35

RT125D - PARTS CATALOGUE

Brand: HYOSUNG Pages: 73

Brand: MARTINDALE Pages: 39

Brand: Healtech Pages: 2

Brand: Healtech Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands