Huawei Airbridge BTS3606A Installation Manual Download Page 53

Page: 53 / 141

Installation Manual – BTS3606A Cabinet Installation
Airbridge BTS3606&3606A CDMA Base Station

Chapter 3 Installing Cabinet and Cabinet Equipment

Huawei Technologies Proprietary

3-14

Figure 3-13

Installing a board (2)

Tighten the screws clockwise on the front panel. See Figure 3-14.

Figure 3-14

Installing a board (3)

3.4.2 Installing Modules in RF Subrack

Modules in the RF subrack include CCDU, CTRM/CMTR, CMPA/CHPA. Their

installation procedures are similar.

Caution:

The transmit and receive performance of the BTS may degrade if the screws are

fastened before the CTRM/CMTR, CDDU, and other RF modules are placed in

position.

To install a module in the RF subrack, proceed as follows:

Summary of Contents for Airbridge BTS3606A














































































































































Search results

Summary of Contents for Airbridge BTS3606A

Reviews:

Related manuals for Airbridge BTS3606A

Brands by name

Popular brands

Huawei Airbridge BTS3606A, Installation Manual

Search results

Summary of Contents for Airbridge BTS3606A

Reviews:

Related manuals for Airbridge BTS3606A

Brands by name

Popular brands