Huawei Airbridge BTS3606A Installation Manual Download Page 8

Page: 8 / 141

Installation Manual – BTS3606A Cabinet Installation
Airbridge BTS3606&3606A CDMA Base Station

Table of Contents

Huawei Technologies Proprietary

Table of Contents

Chapter 1 Installation Preparations............................................................................................. 1-1

1.1 Project Files ....................................................................................................................... 1-1

1.2 Tools and Instruments ....................................................................................................... 1-2

1.3 Installation Conditions........................................................................................................ 1-3

1.3.1 Site Requirements................................................................................................... 1-3

1.3.2 Load-bearing Capacity Requirements .................................................................... 1-3

1.3.3 Space Requirements............................................................................................... 1-4

1.3.4 Power Supply and Grounding Requirements.......................................................... 1-5

1.3.5 Requirements for Transmission System ................................................................. 1-5

1.3.6 Requirements for Antenna System ......................................................................... 1-5

1.4 Unpacking .......................................................................................................................... 1-5

1.4.1 Unpacking Requirements........................................................................................ 1-6

1.4.2 Unpacking Wooden Case ....................................................................................... 1-7

1.4.3 Unpacking Carton ................................................................................................... 1-9

Chapter 2 Installing Cabinet Base or Channel Steel.................................................................. 2-1

2.1 Introduction to Cabinet Base ............................................................................................. 2-1

2.1.1 Base for BTS3606A Cabinet ................................................................................... 2-1

2.1.2 Base for Battery Cabinet ......................................................................................... 2-1

2.2 Installation Flowchart ......................................................................................................... 2-2

2.3 Installing Cabinet Base ...................................................................................................... 2-3

2.3.1 Laying Out Installation Position............................................................................... 2-3

2.3.2 Casting Cement Plinth ............................................................................................ 2-5

2.3.3 Positioning the Base ............................................................................................... 2-6

2.3.4 Drilling Holes and Installing Expansion Bolts.......................................................... 2-8

2.3.5 Fastening the Base ............................................................................................... 2-10

2.4 Installing Channel Steel ................................................................................................... 2-11

2.4.1 Laying out Installation Position.............................................................................. 2-12

2.4.2 Casting Cement Plinths......................................................................................... 2-12

2.4.3 Preparing Channel Steel ....................................................................................... 2-12

2.4.4 Positioning Channel Steel ..................................................................................... 2-12

2.4.5 Drilling Holes and Installing Expansion Bolts........................................................ 2-12

2.4.6 Fastening Channel Steel....................................................................................... 2-12

Chapter 3 Installing Cabinet and Cabinet Equipment ............................................................... 3-1

3.1 Installation of Cabinet ........................................................................................................ 3-1

3.1.1 Positioning Cabinet ................................................................................................. 3-1

3.1.2 Leveling Cabinet...................................................................................................... 3-2

3.1.3 Fastening Cabinet ................................................................................................... 3-4

Summary of Contents for Airbridge BTS3606A














































































































































Search results

Summary of Contents for Airbridge BTS3606A

Reviews:

Related manuals for Airbridge BTS3606A

Brands by name

Popular brands

Huawei Airbridge BTS3606A, Installation Manual

Search results

Summary of Contents for Airbridge BTS3606A

Reviews:

Related manuals for Airbridge BTS3606A

Brands by name

Popular brands