HP X Class 500/550MHz Reference Manual Download Page 131

Page: 131 / 149

Chapter 5

131

Tests and Error Messages

Error Message Summary

0711h

Defective SIMM (module 1, bank 1)

System Memory Error

0712h

Defective SIMM (module 2, bank 1)

System Memory Error

0721h

Defective SIMM (module 1, bank 2)

System Memory Error

0722h

Defective SIMM (module 2, bank 2)

System Memory Error

0731h

Defective SIMM (module 1, bank 3)

System Memory Error

0732h

Defective SIMM (module 2, bank 3)

System Memory Error

0800h

Found lower cache size than configured

System Cache Error

0801h

Cache self-test failure

System Cache Error

0900h

Lan (Chanteclerc) self-test failure

Integrated LAN Error

0901h

Lan (Chanteclerc) not detected (but enabled
in Setup)

Integrated LAN Error

0A00h

Plug and Play video auto-setting failure
(DDC hang)

DDC Video Error

Table 5-5. Error Codes, Causes and Symptoms

Code #

Cause / Symptom

Short message (US)

Summary of Contents for X Class 500/550MHz






















































































































































Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands

HP X Class 500/550MHz, Reference Manual

Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands