HP X Class 500/550MHz Reference Manual Download Page 68

Page: 68 / 149

Chapter 3

Interface Boards and Mass-Storage

Drivers

ELSA GLoria AGP Graphics Board

HP V

ISUALIZE

Personal Workstation models are supplied with an ELSA GLoria

™ AGP graphics board fitted in the AGP accessory slot. There is a total of 8 MB
of video Synchronous Graphics RAM (SGRAM) memory installed on the graphics board
which cannot be upgraded.

The Permedia 2A graphics processor communicates directly with the Pentium II processor
along the AGP bus.

Features

• Optimized all-round capabilities in 2 D and 3 D.

• High resolution with 1900 x 1200 pixels in HiColor.

• 2D performance and high-power 3D hardware acceleration.

• Multi-screen support for Windows NT (with PCI ELSA GLoria graphics

boards).

• Supports 16: 10 wide-format monitors.

Specifications

• Supports basic AGP mode (66 MHz).

• Serial EEPROM video BIOS interface (up to 64 KB).

• AGP ATX form factor compliant.

• PERMEDIA 2A graphics processor.

• Pixel clock maximum frequency of 250 MHz.

• 3D coprocessor. Integrated GLINT Delta graphics setup processor.

• 3D standards. Hardware accelerated OpenGL, HEIDI, Direct3D.

• 4 MB of video SGRAM memory installed on the graphics board. Added to this, there is a

pre-installed 4 MB SO_DIMM video memory module, giving a total of 8 MB (this is the
maximum amount of video memory possible).

• Standards: VESA Video BIOS, DPMS, DDC2B, Plug & Play.

• Video standards: DirectDraw, ActiveMovie 1.0, DirectShow

(ActiveMovide 2.0).

Summary of Contents for X Class 500/550MHz






















































































































































Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands

HP X Class 500/550MHz, Reference Manual

Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands