HP X Class 500/550MHz Reference Manual Download Page 104

Page: 104 / 149

104

Chapter 4

HP BIOS

BIOS Addresses

This section provides a summary of the main features of the HP system BIOS. This is
software that provides an interface between the computer hardware and the operating
system.

The procedure for updating the System ROM firmware is described in the section
“Updating the System ROM” in the chapter “System Board.”

System Memory Map

Reserved memory used by accessory boards must be located in the area from C8000h to
EFFFFh.

Table 4-3. System Memory Map

0000 0000 - 0000 03FF

Real-mode IDT

0000 0400 - 0000 04FF

BIOS Data Area

0000 0500 - 0009 FC00

Used by Operating System

0009 FC00 - 0009 FFFF

Extended BIOS Data Area

000A_0000 - 000B_FFFF

Video RAM or SMRAM (not visible unless in SMM)

000C 0000 - 000C 7FFF

Video ROM (VGA ROM)

000C 8000 - 000F FFFF

Adapter ROM, RAM, memory-mapped registers, BIOS

000E 0000-000F FFFF

128 KB BIOS (Flash/Shadow)

0001 0000-000F FFFF

Memory (1 MB to 16 MB)

0010 0000-001F FFFF

Memory (16 MB to 32 MB)

0020 0000-003F FFFF

Memory (32 MB to 64 MB)

0040 0000-007F FFFF

Memory (64 MB to 128 MB)

0080 0000-7FFF FFFF

Memory (128 MB to 2 GB)

FECO 0000

I/O APIC

FEEO 0000

Local APIC (each CPU)

FFFE 0000-FFFF FFFF

128 KB BIOS (Flash)

Summary of Contents for X Class 500/550MHz






















































































































































Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands

HP X Class 500/550MHz, Reference Manual

Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands