HP X Class 500/550MHz Reference Manual Download Page 79

Page: 79 / 149

Chapter 3

Interface Boards and Mass-Storage

Drivers

SCSI/LAN Combination Board

On the rear panel there is one RJ-45 connector. There is a LED which indicates the LAN
connection status as follows:

• Off - when there is no response (for example, when the LAN cable is not connected to

the network HUB.

• Blinking - during Autonegotiation

• Green (ON) - the connection has passed the Autonegotiation and a link has been

established between the LAN adapter and the network HUB/Switch.

NOTE

Refer to the User’s Guide for details concerning system configuration changes

necessary after installing a LAN adapter.

10BT/100TX LAN Features

Remote Power On

Remote Power On (RPO) is available at 10 and 100 Mbits per second.

Vstandby requirements supporting RPO

The Vstandby requirement for the HP network card supporting RPO, is: a power supply
able to deliver at least 720 mA on Vstandby output. This is the case for all HP V

ISUALIZE

systems.

Table 3-6. 10BT/100TX LAN Features

Feature

Description

LAN Controller

AMD PCNET-Fast+ chip

RJ45 Connector

10BT/100TX autonegotiation

Remote Boot

Protocols integrated in System BIOS

ExtStart Connector

Connection to CPU board

Remote Power On (RPO)

Full remote power on with Magic Packet

Remote Wake Up (RWU)

Wake Up from Suspend state with Magic Packet

Wake On LAN (WOL)

Enables a host computer, using Magic Packet technology, to remotely
(over the network) power on computers.

Summary of Contents for X Class 500/550MHz






















































































































































Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands

HP X Class 500/550MHz, Reference Manual

Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands