HP X Class 500/550MHz Reference Manual Download Page 78 | Manualshive

Page: 78 / 149

background image

78

Chapter 3

Interface Boards and Mass-Storage

Drivers

SCSI/LAN Combination Board

10BT/100TX LAN Controller

The embedded 10BT/100TX LAN controller supports the following standards: 100 Mbits
per second over 2-pair, category-5, unshielded twisted pair (UTP), or shielded twisted pair
(STP); 10 BaseT, 10 Mbits per second, ISO 8802-3 (IEEE 802.3 standard).

The LAN adapter contains two internal connectors.

• Wake On LAN (WOL) which enables a host computer, using Magic Packet technology, to

remotely (over the network) power on computers (Remote Power On) or wake them up
(Remote Wake Up) from energy-saving Sleep mode.

For these functions to work, the WOL cable must be connected between the three-pin
connector (J8), on the SCSI/LAN Combination board, and the WOL connector on the
system board. Refer to the section “SCSI/LAN Combination Board” in this chapter to
locate the position of the J8 connector on the SCSI/LAN combination board and refer to
the section “System Board Overview” in the chapter “System Board” for the WOL
connector on the system board.

The LAN adapter that uses the Remote Power On feature must be installed further
from the processors than any other supplementary LAN adapter card. How to use the
Remote Power On feature is described in detail in the User’s Guide provided with the
PC Workstation.

• External Start connector which enables LAN activity, the SCSI LED activity on the

front panel for SCSI hard disk drive accesses, and external SCSI cable detection.

The external cable must be connected between the thirteen-pin connector (J4), on the
SCSI/LAN combination board, to the HP External Start connector on the system board.

Refer to the section “SCSI/LAN Combination Board” in this chapter for the position of
the J4 connector on the SCSI/LAN combination board and refer to the section “System
Board Overview” in the chapter “System Board” for the HP External Start connector
position on the system board.

Table 3-5. 10BT/100TX LAN Adapter Internal Connectors

Connector

Description

Location

J4

External Start connector, 13-pin. Enables LAN
activity, SCSI Led activity on the front panel
for hard disk drive accesses, and external SCSI
cable detection.

Located near the J9 connector.

J9

Wake On LAN connector, 3-pin. Enables a host
computer to remotely power on computers
(over the network).

Located between the J9 and J3
connectors.

«
...
76
77
78
79
80
...
»

Summary of Contents for X Class 500/550MHz






















































































































































Reviews:

No comments

Related manuals for X Class 500/550MHz

Brand: ID Systems Pages: 12

Brand: Qlogic Pages: 2

SANblade 2300 Series

Brand: Qlogic Pages: 108

Brand: Qlogic Pages: 2

Brand: Qlogic Pages: 2

SANblade QLA2342

Brand: Qlogic Pages: 16

SANblade QLA4050

Brand: Qlogic Pages: 4

Brand: Telex Pages: 6

Freedom SW 2000

Brand: Xantrex Pages: 36

CrossPower C4L5200-ETH

Brand: C4Line Pages: 26

Brand: Weego Pages: 6

Brand: HomeSpot Pages: 12

USB-IrDA Adapter

Brand: Hama Pages: 13

USB Power Adapter A04-PAU02

Brand: Atlantis Land Pages: 2

Brand: Xoro Pages: 12

Brand: Titan Electronics Pages: 76

FRITZ!Powerline 510E Set

Brand: AVM Pages: 38

BasicXL BXL-NBT-AC01

Brand: nedis Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands