HP X Class 500/550MHz Reference Manual Download Page 23 | Manualshive

Page: 23 / 149

background image

Chapter 1

23

System Overview

Specifications and Characteristics Data

An attempt to draw too much current (such as, a short circuit across edge-connector pins, or an
accessory board that is not suitable for these Personal Workstations), will cause the overload
protection in the power supply to be triggered, and the Personal Workstation could fail to boot.

NOTE

When the Personal Workstation is turned off with the power button on the
front panel, the power consumption falls below the low power level (refer to
Table 1-5), but is not zero. The special on/off method used by this Personal
Workstation extends the lifetime of the power supply. To reach zero power
consumption in “off ” mode, either unplug the Personal Workstation form the
power outlet or use a power block with a switch.

Max current
at
+5 Vstdby

0.72 A

—

—

—

—

1. PCI and AGP power electrical specifications must be respected. For example, the maximum power

consumption for the PCI slot is 25 W. The total power PCI consumption must never exceed 85 W. For the
AGP slot, 2 A maximum at +5 V.

Table 1-4. Electrical Specifications

Parameter

Total Rating

Notes

Maximum

per PCI

Slot

Maximum

for ISA

Slot

Maximum for

AGP Slot

«
...
21
22
23
24
25
...
»

Summary of Contents for X Class 500/550MHz






















































































































































Reviews:

No comments

Related manuals for X Class 500/550MHz

D DPH-50U DPH-50U

Brand: D-Link Pages: 2

AirPlus DWL-810

Brand: D-Link Pages: 64

Brand: D-Link Pages: 39

Brand: D-Link Pages: 8

802.11g Wireless LAN USB Adapter DWL-G122

Brand: D-Link Pages: 43

AirPlusXtremeG DWL-G650

Brand: D-Link Pages: 20

Brand: Yeastar Technology Pages: 52

Brand: Aztech Pages: 2

Brand: Modecom Pages: 24

Brand: Alvarion Pages: 2

Dual Port 25 Gb

Brand: Oracle Pages: 88

Brand: StarTech.com Pages: 10

Brand: Emulex Pages: 19

Brand: ZyXEL Communications Pages: 28

Brand: Lindy Pages: 16

Brand: Sygonix Pages: 8

Brand: Renesas Pages: 20

Brand: Sensaphone Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands