HP X Class 500/550MHz Reference Manual Download Page 107 | Manualshive

Page: 107 / 149

background image

Chapter 4

107

HP BIOS

BIOS Addresses

Interrupt Controllers

The system has an APIC (82093AA) I/O interrupt controller and two 82C59 “legacy”
interrupt controllers.

The following table shows how the “legacy” interrupts are connected to the APIC
controller. The Interrupt Requests (IRQ) are numbered sequentially, starting with the
master controller, and followed by the slave (both of 82C59 type).

NOTE

Although the Setup program can be used to change some of the settings, the
following address map is not completely BIOS dependent, but is determined
partly by the operating system. Note that some of the I/O addresses are
allocated dynamically.

Table 4-6. The Relationship of the “Legacy” Interrupts to the APIC Controller

I/O APIC Input

IRQ

Interrupt Request Description

INTIN0

PIIX4E INTR

INTIN1

IRQ1

NS317 Keyboard Controller

INTIN2

IRQ0

PIIX4E System Timer

INTIN3

IRQ3

NS317 COM2, COM4

INTIN4

IRQ4

NS317 COM1, COM3

INTIN5

IRQ5

AD1816, LPT2

INTIN6

IRQ6

NS317 Flexible Disk Controller

INTIN7

IRQ7

NS317 LPT1

INTIN8

IRQ8

NS317 RTC

INTIN9

IRQ9

INTIN10

IRQ10

INTIN11

IRQ11

AD1816 MIDI

INTIN12

IRQ12

NS317 Mouse

INTIN13

not connected

INTIN14

IRQ14

PIIX4E IDE Channel 1

INTIN15

IRQ15

INTIN16

PCINTA

INTIN17

PCINTB

INTIN18

PCINTC

INTIN19

PCINTD

INTIN20

TFPC IRQ

INTIN21

SCI IRQ

INTIN22

not connected

INTIN23

PIIX4E SMI
(not used)

«
...
105
106
107
108
109
...
»

Summary of Contents for X Class 500/550MHz






















































































































































Reviews:

No comments

Related manuals for X Class 500/550MHz

Brand: Vantec Pages: 15

SmartSwitch 6C110

Brand: Cabletron Systems Pages: 7

Brand: cable matters Pages: 52

Brand: CoolGear Pages: 19

Brand: Tripp Lite Pages: 2

NWD-210N - V1.0

Brand: ZyXEL Communications Pages: 152

RTE7702012EAB00000J

Brand: Renesas Pages: 53

Brand: TP-Link Pages: 30

MISMATCH IS II BRAKE TO SRAM SHIFTER/DROPPER

Brand: Problem Solvers Pages: 8

USB VGA Display Adapter

Brand: J5create Pages: 48

Brand: Laser Pages: 2

Brand: White Rodgers Pages: 8

Brand: Sophos Pages: 32

Brand: DigiPower Pages: 12

Brand: Allen-Bradley Pages: 12

Brand: Dynafit Pages: 17

Pavilion zd7000 - Notebook PC

Brand: Compaq Pages: 46

Brand: SOHARD Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands