HP X Class 500/550MHz Reference Manual Download Page 24 | Manualshive

Page: 24 / 149

background image

24

Chapter 1

System Overview

Specifications and Characteristics Data

Operating temperature and humidity ranges may vary depending upon the mass storage devices
installed. High humidity levels can cause improper operation of disk drives. Low humidity levels
can aggravate static electricity problems and cause excessive wear of the disk surface.

Table 1-5. Power Consumption

Power Mode

Power Consumption

Operating

85 W (average)

Idle

75 W (average)

Off

6.5 W (average)

Table 1-6. Environmental Specifications

Environmental Specifications (System Processing Unit, with Hard Disk)

Operating Temperature

+5˚C to +40˚ (+40˚F to +104˚F)

Storage Temperature

−

40˚C to +70˚C (

−

40˚F to +158˚F)

Over Temperature Shutdown

+50˚C (+122˚F)

Operating Humidity

15% to 80% (relative)

1

Storage Humidity

8% to 80% (relative)

1

Acoustic noise emission:
Sound power – with 10.0krpm SCSI hard disk drive

(as defined by ISO 7779)
LwA < 50 db

Operating Altitude

10000 ft (3100m) max

Storage Altitude

15000 ft (4600m) max

1. Non-condensing conditions

«
...
22
23
24
25
26
...
»

Summary of Contents for X Class 500/550MHz






















































































































































Reviews:

No comments

Related manuals for X Class 500/550MHz

Brand: Dynex Pages: 12

Brand: Keithley Pages: 43

Brand: Hi-flying Pages: 19

CS1001 - Single

Brand: BOB Pages: 19

Component Video Adapter

Brand: ATI Technologies Pages: 16

Brand: Hawg Wired Pages: 10

Brand: Keysight Technologies Pages: 24

Brand: Vega Pages: 24

Brand: LM Technologies Pages: 27

Brand: Digitus Pages: 7

Brand: Natec Pages: 34

Brand: TRENDnet Pages: 18

DPPA-BT1 - Bluetooth USB Adaptor

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

DAVHDX279W - BRAVIA Theater System

Brand: Sony Pages: 2

Brand: Sony Pages: 5

Cyber-shot DCC-L1

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands