HP X Class 500/550MHz Reference Manual Download Page 85

Page: 85 / 149

Chapter 3

Interface Boards and Mass-Storage

Drivers

Mass-Storage Drives

• Photo-CD Multisession.

• CD Audio disk.

• Mixed mode CD-ROM disk (data and audio).

• CD-ROM XA, CD-I, CD-Extra, CD-R, CD-RW.

Table 3-9. IDE 32X CD-ROM Drive

Description

HP product number

D4384A

Disk Diameter

120mm

Data Block Size

2,048 bytes (Mode-1)
2,336 bytes (Mode-2)

Storage Capacity

650 Mbytes (Mode-1)
742 Mbytes (Mode-2)

Read Mode

Full CAV

14X to 32X

CAV = Constant Angular Velocity

Burst Transfer Rate

PIO mode 4 - 16.6 Mbytes/s maximum
Single Word DMA Mode 2 - 8.3 Mbytes/s maximum
Multi Word DMA Mode 2 - 16.6 Mbytes/s maximum

Access Time

Average Stroke (1 / 3) 110 ms
Full Stroke 180 ms

Data Error Rate

Less than 10-12 (Mode-1)

Less than 10-9 (Mode-2)

It is assumed that raw error rate of disk is 10-3 in the worst case. This excludes “retries.”

Spin Up Time

From standby mode. Typical 6s to drive ready mode.

With tray loading. Typical 8.5s to drive ready mode.

Photo-CD (Multisession) is not applicable.

Buffer Memory Size

128 kbytes

Summary of Contents for X Class 500/550MHz






















































































































































Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands

HP X Class 500/550MHz, Reference Manual

Search results

Summary of Contents for X Class 500/550MHz

Reviews:

Related manuals for X Class 500/550MHz

Brands by name

Popular brands