HP OmniBook VT6200 Manual Download Page 93 | Manualshive

Page: 93 / 189

background image

Add-On Devices

Replacing the Hard Disk Drive

Corporate Evaluator’s Guide

93

To replace the hard disk drive holder

If you are installing a new hard drive that does not have a holder, you can remove the
holder parts from the old hard drive. You’ll need a small Phillips screwdriver for this
procedure.

1.

Remove the six screws from the holder and drive case, then lift the drive out of the
holder.

2.

Notice that the hard drive has a pin connector attachment at one end. Carefully
remove this connector from the end of the drive. Work alternately at each end so that
the connector slides off evenly without bending the connector pins.

3.

Carefully put the pin connector attachment back onto the pins on the end of the new
hard drive. Work alternately at each end so that the connector slides on evenly
without bending the connector pins.

4.

Insert the connector through the end of the holder, and lower the drive into the holder.

5.

Reinstall the screws into the holder and drive case.

«
...
91
92
93
94
95
...
»

Summary of Contents for OmniBook VT6200






























































































































































































Reviews:

No comments

Related manuals for OmniBook VT6200

Brand: NEC Pages: 34

VERSA 6220 - SERVICE

Brand: NEC Pages: 199

ShieldPRO FC-N21S

Brand: NEC Pages: 20

TravelMate 4210

Brand: Acer Pages: 84

Brand: Omen Pages: 15

Brand: AORUS Pages: 91

Brand: NEC Pages: 27

Brand: Clevo Pages: 99

Brand: EUROCOM Pages: 104

Brand: Acer Pages: 85

Brand: Acer Pages: 76

Brand: Acer Pages: 80

Brand: Acer Pages: 87

TravelMate P2 Series

Brand: Acer Pages: 57

Brand: Acer Pages: 87

Brand: Acer Pages: 78

Aspire 5332 Series

Brand: Acer Pages: 11

ASPIRE ASPIRE X1700

Brand: Acer Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands