HP OmniBook VT6200 Manual Download Page 149

Page: 149 / 189

Troubleshooting and Maintenance

Configuring the Computer

Corporate Evaluator’s Guide

149

Main Menu

Setting

Description

Default

BIOS Revision

Shows the current BIOS version.

Detected
automatically.

System Time

Sets the time using 24-hour format. Values set take effect
immediately.

System Date

Sets the date using dd/mm/yy format (except English, which
uses mm/dd/yy format).

Internal Hard Disk

Sets the hard disk drive type and various parameters.

Detected
automatically.

Video Configuration

Press ENTER to see or change the video settings below.
Press ESC to return to the main menu.

Quiet Boot

When enabled, hides summary of power-on self-test and
messages during boot.

Enabled

Video Display Device

Sets whether the built-in display automatically switches to an
external display, if one is detected.

Auto

Video Expansion

When enabled, the video image covers the entire display in
lower resolution modes. When disabled, the video image is
centered in the display.

Disabled

Primary Video

Adapter

Sets whether the computer automatically switches to an
external video adapter connected to the docking system, if
one is detected.

Auto

Television Type

Controls the signal format (NTSC or PAL) output by the
S-video port.

NTSC

System Memory

Shows the system memory size.

640 KB

Extended Memory

Shows the extended memory size.

Detected
automatically.

Unique Dock ID

Sets whether the computer creates a unique hardware profile
for each dock (Enabled) or uses a common profile for all
docks (Disabled).

Enabled

UUID

Displays the value of the 16-byte UUID (Universally Unique
ID) as 32 hex characters.

Detected
automatically.

MAC Address

Displays the MAC network address of the internal (wired)
LAN.

Detected
automatically.

Serial Number

Displays the serial number as shown on the back of the unit.

Detected
automatically.

Service ID

Displays an identifier used for repair service.

Detected
automatically.

Summary of Contents for OmniBook VT6200






























































































































































































Search results

Summary of Contents for OmniBook VT6200

Reviews:

Related manuals for OmniBook VT6200

Brands by name

Popular brands

HP OmniBook VT6200, Manual

Search results

Summary of Contents for OmniBook VT6200

Reviews:

Related manuals for OmniBook VT6200

Brands by name

Popular brands