HP OmniBook VT6200 Manual Download Page 112

Page: 112 / 189

Installing Windows 2000
Installing Retail Windows 2000

112

Corporate Evaluator’s Guide

Important

Before installing Windows 2000, please install the latest BIOS for your HP notebook.
To check your BIOS version do the following:

Start the HP notebook.

Press F2 to Enter setup when prompted.

Check the BIOS Version in the upper left corner.

You can download the latest HP Notebook BIOS from http://www.hp.com/notebooks.

To prepare for software installation

Hewlett-Packard recommends that you repartition your hard disk before installing
Windows 2000. This will add hard disk-based diagnostics to make support easier. Follow
the instructions below to repartition your hard disk.

Connect the AC adapter to the notebook.

Insert the CD-ROM/DVD drive into the notebook.

Insert the bootable Recovery CD into the CD-ROM/DVD drive.

Reboot and press ESC when you see the HP Notebook logo.

Select CD-ROM DRIVE as the boot device.

Click 2 CONTINUE.

Click 2 ADVANCED.

Select your desired Hibernate Partition Size (0M is the preferred size for Windows
2000)

Check DO NOT LOAD OPERATING SYSTEM.

10.

Select HIBERNATE PARTITION ONLY.

11.

Click 1 CONTINUE.

12.

Click OK.

13.

Remove the Recovery CD from the CD-ROM/DVD drive.

Summary of Contents for OmniBook VT6200






























































































































































































Search results

Summary of Contents for OmniBook VT6200

Reviews:

Related manuals for OmniBook VT6200

Brands by name

Popular brands

HP OmniBook VT6200, Manual

Search results

Summary of Contents for OmniBook VT6200

Reviews:

Related manuals for OmniBook VT6200

Brands by name

Popular brands