HP HPE Alletra 6010 Hardware Manual Download Page 104

Page: 104 / 117

Hardware and Model Specifications

This section describes the environmental, electrical, and physical specifications of HPE storage arrays.

Hardware Specifications

Generic specifications that apply to all models appear first, followed by model-specific hardware specifications.

Table 8: Chassis Dimensions and Weight

Specification

Component

17.58 cm (6.93 in)

Height

43.88 cm (17.28 in)

Width

79.98 cm (31.49 in)

Depth

Rack Units

Chassis with 2.5-inch SSDs: up to 54.5 kg (120 lb)

Approximate Weight

Table 9: Operating Environment

Specification

Component

Operating: 10° to 35° C (50° to 95° F)

Temperature

Operating: 8 to 90% non-condensing

Humidity

Operating: -305 to 3048 m (-1000 to 10,000 feet)

Altitude

Hardware and Model Specifications 104

Documentation Feedback: [email protected]

Summary of Contents for HPE Alletra 6010






















































































































Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands

HP HPE Alletra 6010, Hardware Manual

Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands