HP HPE Alletra 6010 Hardware Manual Download Page 47

Page: 47 / 117

Figure 18: Front LEDs

Controller health status

Power button

Power status

Controller B ID button

Controller power status

Controller A ID button

The following table describes the front LEDs.

Status

LED

Solid green indicates that the array is powered on

Power button

•

Solid green indicates that power from all installed power
supplies is within range

•

Amber indicates that power from installed power supplies
is out of range

•

Off indicates the array is powered off

The power status LED remains green for a missing PSU.

Power status

Blue LED inside the ID button changes state when the button
is pushed or when an ID command is received

•

Blinking blue indicates that reboot is in progress

•

Solid blue indicates the controller is activated

Controller ID button

•

Solid green indicates the controller is running and system
status is healthy

•

Blinking green indicates the controller is rebooting

•

Blinking amber indicates the controller is operating in a
degraded or critical state

•

Solid amber indicates that the controller is halted or has
failed

Controller health status

•

Solid green indicates the controller is powered on

•

Blinking green indicates that power on is in progress

•

Solid amber indicates controller is in power standby

•

Off indicates the controller is powered off

Controller power status

Array Components 47

Documentation Feedback: [email protected]

Summary of Contents for HPE Alletra 6010






















































































































Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands

HP HPE Alletra 6010, Hardware Manual

Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands