HP HPE Alletra 6010 Hardware Manual Download Page 106

Page: 106 / 117

Description

Item

10Gb/s (9.95 to 10.5)

10Gb/s (9.95 to 10.3)

Data Rate

850nm VCSEL laser

Wavelength

10GBASE-SR/SW 10Gb/s Ethernet

Applications

3.3V

Voltage, per power supply

LC Duplex

Connector type

RoHS-6 compliant (lead free)

RoHS

0° to 70°C (32° to 158°F)

-5° to 70°C (23° to 158°F)

Operating temperature

300m on 2000 MHz multimode fiber

400m on OM4 multimode fiber

Maximum link length

802.3ae

802.3-2012

IEEE Standard

Table 12: Applied Optoelectronics

Description

Item

Applied Optoelectronics A7ELSN85ADMA0684

Manufacturer / Part number

Multimode

Media type

10Gb/s

Data Rate

850nm VCSEL laser

Wavelength

10GBASE-SR Ethernet 10Gb/s Ethernet

Applications

3.3V

Voltage, per power supply

Dual LC

Connector type

2011/65/EU

RoHS

-5° to 70°C (23° to 158°F)

Operating temperature

300m on OM3 multimode fiber

Maximum link length

802.3ae

IEEE Standard

SFP28 Specifications (25GbE)

Table 13: Avago

Description

Item

Avago AFBR-725SMZ

Manufacturer / Part number

Multimode

Media type

25Gb/s

Data Rate

850nm VCSEL laser

Wavelength

Ethernet NIC Cards/Adapters

Applications

3.3V

Voltage, per power supply

LC Duplex

Connector type

RoHS-compliant

RoHS

Hardware and Model Specifications 106

Documentation Feedback: [email protected]

Summary of Contents for HPE Alletra 6010






















































































































Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands

HP HPE Alletra 6010, Hardware Manual

Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands