HP HPE Alletra 6010 Hardware Manual Download Page 76

Page: 76 / 117

Replace an AC Power Supply

Use this procedure to replace a failed AC power supply unit (PSU) on your HPE storage array or expansion shelf.

Before you begin

5 to 10 minutes

Time required:

Replacement AC power supply ordered from HPE

Parts required:

•

RMA (Return Materials Authorization) work order

•

Case number

•

Array name or serial number

The array serial number can be found on the pullout System Info tab.

Information required:

See Support.

Support contact:

HPE recommends using the Maintenance Window functionality within the HPE InfoSight portal to inform HPE Support of
upcoming maintenance windows.

Refer to https://infosight.hpe.com/dashboards/nimble/wellness/maintenance-windows for more information.

You can disable automated support case generation during planned maintenance from the Manage Maintenance Windows
page. After a maintenance window is set, no further communication with HPE Support is required.

Note:

Before you attempt to replace a power supply:

•

Do not remove the PSU until you are ready to install the
replacement

•

Never unplug or unseat both PSUs at the same time

•

Both PSUs in a controller or expander must be the same

•

Use only UL-approved power cords

Procedure

1. Identify the power supply to replace. In the software, the right power supply is PSU1, and the left power supply is PSU2.

2. Remove the power cord from the PSU.

3. Push the power supply release lever to the left, grasp the handle, and pull out the power supply.

Power supply handle

Power supply LED

2 Power supply release lever

4. Insert the new PSU. Push in gently until you hear a click.

Maintenance Procedures 76

Documentation Feedback: [email protected]

Summary of Contents for HPE Alletra 6010






















































































































Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands

HP HPE Alletra 6010, Hardware Manual

Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands