HP HPE Alletra 6010 Hardware Manual Download Page 80 | Manualshive

Page: 80 / 117

background image

Replacement DC power supply ordered from HPE

Parts required:

•

RMA (Return Material Authorization) work order

•

Case number

•

Array serial number

Information required:

•

ESD (electrostatic discharge) strap or appropriate grounding device

•

Phillips screwdriver

Tools required:

Support contact:

HPE recommends using the Maintenance Window functionality within the HPE InfoSight portal to inform HPE Support of
upcoming maintenance windows.

Refer to https://infosight.hpe.com/dashboards/nimble/wellness/maintenance-windows for more information.

You can disable automated support case generation during planned maintenance from the Manage Maintenance Windows
page. After a maintenance window is set, no further communication with HPE Support is required.

A PSU with an amber LED may have a fault. But an amber LED also indicates:

•

The external power is switched off with the DC power connected

•

The power supply is not properly seated in its slot

•

The array is powered off

•

A power supply internal fault has occurred

Verify that the power cord is plugged in, then check for and correct these conditions before you assume that the PSU in your
HPE Nimble Storage array needs to be replaced.

CAUTION:

Before you attempt to replace a power supply:

•

Do not remove the PSU until you are ready to install the
replacement

•

Never unplug or unseat both PSUs at the same time

•

Use only UL-approved power cords

Procedure

1. Identify the failed PSU.

The LED on a failed PSU is amber or dark.

2. Remove the power connections.

CAUTION: Before proceeding, verify that the DC power source is turned off at the circuit breaker.

a) Push the power supply release lever to the left, grasp the handle, and pull the power supply out several inches to access

the connector cover.

Maintenance Procedures 80

Documentation Feedback: [email protected]

«
...
78
79
80
81
82
...
»

Summary of Contents for HPE Alletra 6010






















































































































Reviews:

No comments

Related manuals for HPE Alletra 6010

Brand: CalDigit Pages: 21

LaCie Ethernet Big Disk

Brand: LaCie Pages: 16

4BIG QUADRA USB 3.0

Brand: LaCie Pages: 41

5big - Network NAS Server

Brand: LaCie Pages: 9

Brand: LaCie Pages: 14

Brand: LaCie Pages: 13

Brand: LaCie Pages: 29

Brand: LaCie Pages: 4

Z-DRIVE R2 E88 512GB PCI-EXPRESS X8 SSD

Brand: OCZ Pages: 2

Brand: LaCie Pages: 22

BLACKOUT WINDOW STORAGE SYSTEM

Brand: REBEL OFF ROAD Pages: 9

CISCO MDS 9124 - UPDATE FOR SYSTEM STORAGE

Brand: IBM Pages: 37

Brand: Soyntec Pages: 8

Brand: Thecus Pages: 120

NXA-WC80211G-CF

Brand: AMX Pages: 6

Brand: OpenEye Pages: 23

Brand: Seville Classics Pages: 7

Brand: TrueNAS Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands