HP HPE Alletra 6010 Hardware Manual Download Page 41

Page: 41 / 117

1 Serial port

2. Run the serial console software with the following settings:

Data bits:

None

Parity:

None

Flow controller:

Stop bits:

115.2Kbps

Speed:

3. Log in as user admin with the password admin.

Note: You can only log into the active controller. If you cannot log in, move the laptop computer or workstation
connection to the other controller and try to log in again.

After you have logged in, the CLI is ready to accept commands.

What to do next
Type ? to see a list of commands.

Type the command followed by --help to see the usage information for that command.

Complete the Initial Setup Using the CLI

Before you begin

Before you start, fill out the Installation Checklist on page 20. You need the information from the checklist to perform the
initial CLI setup.

Note: Subnet and VLAN configuration is a separate action.

Procedure

1. After you are logged into the active controller, type:

setup

The Terms and Conditions are displayed.

2. Click Enter to read the Terms and Conditions, then type yes to accept them.

3. Type the following information as requested. Example values are shown here.

Important: If you accept an incorrect entry, you must start the setup process again.

Install the HPE Storage Array 41

Documentation Feedback: [email protected]

Summary of Contents for HPE Alletra 6010






















































































































Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands

HP HPE Alletra 6010, Hardware Manual

Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands