HP HPE Alletra 6010 Hardware Manual Download Page 77

Page: 77 / 117

5. Connect the power cord to the power supply.

6. Secure the power cord in the strain relief strap that is attached to the power supply handle.

Strain relief strap

Power cord

2 Power supply handle

7. Connect the power cord to the power source.

Power is automatically restored to the PSU as soon as the cord is plugged in.

Replace AC Power Supplies with DC Power Supplies

Use this procedure to replace the AC power supply units (PSUs) on your HPE storage array with DC PSUs.

One PSU can adequately power the array while the other PSU is being replaced.

Note: During PSU replacement, the array will run properly while powered with AC and DC power sources at the same
time.

Before you begin

10 to 15 minutes

Time required:

Replacement DC power supplies ordered from HPE

Parts required:

•

Case number

•

Array serial number

Information required:

•

ESD (electrostatic discharge) strap or appropriate grounding device

•

7/16-inch (11 mm) torque wrench

•

Phillips screwdriver

Tools required:

See Support.

Support contact:

HPE recommends using the Maintenance Window functionality within the HPE InfoSight portal to inform HPE Support of
upcoming maintenance windows.

Refer to https://infosight.hpe.com/dashboards/nimble/wellness/maintenance-windows for more information.

Maintenance Procedures 77

Documentation Feedback: [email protected]

Summary of Contents for HPE Alletra 6010






















































































































Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands

HP HPE Alletra 6010, Hardware Manual

Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands