HP HPE Alletra 6010 Hardware Manual Download Page 23 | Manualshive

Page: 23 / 117

background image

Precaution

Consideration

Mount the equipment so that the mechanical loads on the rack are even top-to-bottom, front-to-back,
and side-to-side.

Mechanical Load-
ing

Be sure there is adequate power service to prevent overloading the circuits. Check the ratings of each
item of equipment on each circuit.

Note: The power supplies are 220VAC or 110VAC auto-detecting.

Circuit Overloading

You must provide reliable grounding (earthing) of rack-mounted equipment. In addition, pay attention
to supply connections from the branch circuit, such as power strips.

Reliable Grounding

Install the Array

Use this procedure to install the following array models: HPE Alletra 6010, 6030, 6050, 6070, and 6090.

Before you begin

Attention:

If you are installing more than one storage array, refer to the Hardware Guide available on HPE InfoSight for information
about your model.

https://infosight.hpe.com/org/c2165d17-4d55-4954-83e3-60556a7bb6c8/resources/nimble/docs

What you need for each array:

•

19-inch four-post rack. The provided rails fit both round-hole and square-hole racks.

•

4U space available in the 19-inch rack

•

At least two Ethernet cables for management, one cable per controller

•

At least two cables, Ethernet or Fibre Channel, for data

•

One or two switches, depending on your array and network topology. Two 10GbE or Fibre Channel switches are
recommended for high availability and redundancy.

•

Four power outlets, two per controller, on separate circuits

Current for 800 W power supplies with C14 connectors:

•

Steady state current (approximate): 5.6A @ 240V; 11.7A @120V

•

Startup current (approximate): 4.6A @ 240V; 10.3A @ 120V

Current for 1600 W power supplies with C14 connectors (240V only):

•

Steady state current (approximate): 8.9A @ 240V

•

Startup current (approximate): 8.2A @ 240V

Before beginning, download and read the Release Notes, available on HPE InfoSight (https://infosight.hpe.com). If you do not
have an HPE InfoSight account, click Create Account and provide the required information.

Visit the Welcome Center (https://infosight.hpe.com/welcomecenter) for help setting up your HPE storage array. Before you
can start using the array, you must register the array with Data Services Cloud Console. If you do not have an HPE GreenLake
cloud account (https://common.cloud.hpe.com), the Welcome Center can guide you.

Note:

•

Install this product in restricted-access locations only, such as a dedicated equipment room or an electrical closet.
Installation and maintenance must be carried out by qualified personnel.

Install the HPE Storage Array 23

Documentation Feedback: [email protected]

«
...
21
22
23
24
25
...
»

Summary of Contents for HPE Alletra 6010






















































































































Reviews:

No comments

Related manuals for HPE Alletra 6010

DS8000 - ADDITIONAL INFORMATION

Brand: IBM Pages: 5

System Storage TS7600 ProtecTIER Series

Brand: IBM Pages: 132

Brand: IBM Pages: 188

Brand: Park Tool Pages: 2

Brand: Quantum Pages: 68

DLTtape SDLT 600

Brand: Quantum Pages: 142

Brand: Quantum Pages: 16

Brand: Quantum Pages: 8

StorNext QD7000

Brand: Quantum Pages: 17

Brand: Tandberg Data Pages: 81

StorNext QD7000

Brand: Quantum Pages: 39

Brand: Quantum Pages: 98

Brand: Quantum Pages: 12

Brand: Quantum Pages: 2

Brand: Qualstar Pages: 366

Brand: Qualstar Pages: 42

Brand: Qualstar Pages: 177

Brand: Quantum Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands