HP HPE Alletra 6010 Hardware Manual Download Page 60

Page: 60 / 117

Riser card

Guide post

Groove

Connector

d) With the riser cards and connectors properly aligned, press down on the top of the PCIe cage to seat the riser cards

in their connectors.

e) Press down on the fastener and turn the fastener tab one half turn (180°) clockwise to secure the PCIe cage.

7. Move the power supplies from the failed controller to the new controller.

a) Push the power supply release lever to the left, grasp the handle, and pull the power supply out of the bay.

Power supply handle

Power supply release lever

b) Slide the power supply into a bay of the new controller until it clicks into place.
c) Repeat this action with the other power supply. A power supply can be installed in either bay of the new controller.

Maintenance Procedures 60

Documentation Feedback: [email protected]

Summary of Contents for HPE Alletra 6010






















































































































Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands

HP HPE Alletra 6010, Hardware Manual

Search results

Summary of Contents for HPE Alletra 6010

Reviews:

Related manuals for HPE Alletra 6010

Brands by name

Popular brands