OLT S124D Assembly Manual Download | Manualshive

Page: 1 / 35

background image

12x4 Slider Lean-To Storage Shed

Assembly Manual

Version #2.1
May 7, 2019

1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 1

In the event of a missing or broken piece, call the Outdoor Living Today Customer Support Line @ 1-888-658-1658 with-
in 30 days of the delivery of your purchase. It is our commitment to you to courier replacement parts, free of charge,
within 10 business days of this notification. Replacement parts will not be provided free of charge after the 30 day
grace period.

All structures purchased from Outdoor Living Today are covered for a period of one year for defects in manufacturing
and workmanship. Costs incurred for customer installations are not included.

Failure to use supplied parts included in this kit could result in poor product performance and may void your warranty.
Please contact Outdoor Living Today’s Customer Toll Free Line if you plan to deviate from our written instructions.

Thank you for purchasing a
12x4 Slider Lean-To Storage Shed.
Please take the time to identify all
the parts prior to assembly.

Safety Points and Other Considerations
Our products are built for use based on
proper installation on level ground and
normal residential use. Please follow the
instruction manual when building your
shed and retain the manual for future
maintenance purposes.

Customers are responsible for ensuring
a solid, level, well-draining site for
construction.

Please check with your local municipal
or county by-laws before ordering this
product to confirm it complies with
building codes.

- Snow load ratings vary by geographical location. If heavy or wet snowfall occurs, it

is advisable to sweep snow off roof frequently.

- If the product is elevated, any structural and building code requirements are solely

the customer's responsibility, and should be abided by.

- In areas with high or gusty wind conditions, it is advisable to install the structure

securely to the ground.

- Have a regular maintenance plan to ensure screws, doors, windows and parts are

tightly affixed.

Customer agrees to hold Outdoor Living Today and any Authorized
Dealers free of any liability for improper installation, maintenance and
repair.

1
2
3
...
»

Summary of Contents for S124D




































Reviews:

No comments

Related manuals for S124D

Brand: Backyard Products Pages: 72

StorNext QM1200

Brand: Quantum Pages: 9

Brand: Muscle Rack Pages: 2

Brand: Suncast Pages: 28

Brand: JOBO Pages: 20

CANOPIA RUBICON

Brand: Palram Pages: 71

Big Disk USB 2.0

Brand: LaCie Pages: 47

Brand: Addonics Technologies Pages: 8

Brand: IBM Pages: 24

Storwize V5100 Series

Brand: IBM Pages: 130

Brand: IBM Pages: 114

PREMIUM STP7736

Brand: Supatool Pages: 3

SPINPOINT MP4 HM250HJ

Brand: Samsung Pages: 1

Brand: Samsung Pages: 16

SpintPoint M8-DVR

Brand: Samsung Pages: 83

SPINPOINT V40 Series

Brand: Samsung Pages: 115

Desktop Hard Drive USB 2.0

Brand: Verbatim Pages: 116

Brand: Datoptic Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands