HP Compaq dx7300 Reference Manual Download | Manualshive

Page: 88 / 234

background image

6–20

433611-001

Service Reference Guide, dx7300

Removal and Replacement Procedures— Microtower (MT) Chassis

6.9.3 Installing a Drive

Ä

CAUTION:

To prevent loss of work and damage to the computer or drive:

■

If you are inserting or removing a hard drive, shut down the operating system properly, then turn off

the computer. Do not remove a hard drive while the computer is on or in standby mode.

■

Before handling a drive, ensure that you are discharged of static electricity. While handling a drive,

avoid touching the connector. Refer to

Section 5.2, “Electrostatic Discharge Information”

for more

information about preventing electrostatic damage.

■

Handle a drive carefully; do not drop it.

■

Do not use excessive force when inserting a drive.

■

Avoid exposing a hard drive to liquids, temperature extremes, or products that have magnetic fields

such as monitors or speakers.

1. Install four guide screws (two on each side) into the new drive. The screws help guide the

drive into its proper position in the bay.

❏

If this is a new installation, guide screws are provided on the front of the chassis under
the front bezel.

❏

If this is a replacement drive, use the screws removed from the old drive.

✎

There are a total of eight extra guide screws on the front of the chassis. Four have U.S. threads
and four have metric threads. Metric screws have a black finish. U.S. threaded screws have a
silver finish. Make sure to install the appropriate guide screws into the drive.

2. Align the guide screws with the guide slots, then slide the drive into the drive bay, making

sure it is fully seated.

«
...
86
87
88
89
90
...
»

Summary of Contents for Compaq dx7300











































































































































































































































Reviews:

No comments

Related manuals for Compaq dx7300

Brand: Daikin Pages: 20

Brand: TES Pages: 45

dc5800 - Microtower PC

Brand: Compaq Pages: 69

Brand: Biostar Pages: 58

Rexroth 3 842 998 350

Brand: Bosch Pages: 122

Brand: HP Pages: 50

3350 - Cisco NAC Appliance

Brand: HP Pages: 18

290 G2 MT Business

Brand: HP Pages: 7

Brand: HP Pages: 77

299300-006 - Professional - 5100

Brand: HP Pages: 32

Brand: HP Pages: 94

Brand: HP Pages: 12

6080 - Pro Microtower PC

Brand: HP Pages: 4

Brand: HP Pages: 44

300-1020 - TouchSmart - Desktop PC

Brand: HP Pages: 68

Brand: HP Pages: 122

Brand: HP Pages: 140

6000 - ProLiant - 128 MB RAM

Brand: HP Pages: 257

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands