manualshive.com logo in svg

HP Compaq dx7300, Reference Manual

The HP Compaq dx7300 user manual is an essential resource for getting acquainted with this versatile product. Obtain a comprehensive overview of its features and functions through this free manual download available at manualshive.com. Explore your device's potential and unleash its capabilities effortlessly with this user-friendly guide.

Share
Download
background image

C–6

433611-001

Service Reference Guide, dx7730

POST Error Messages

1720-SMART Hard 

Drive Detects Imminent 

Failure

Hard drive is about to 

fail. (Some hard drives 

have a firmware patch 

that will fix an erroneous 

error message.)

1. Determine if hard drive is giving 

correct error message. Enter 

Computer Setup and run the Drive 

Protection System test under 

Storage

 > 

DPS Self-test

.

2. Apply firmware patch if applicable 

(available at www.hp.com/support).

3. Back up contents and replace hard 

drive.

1796-SATA Cabling 

Error

One or more SATA 

devices are improperly 

attached. For optimal 

performance, the SATA 0 

and SATA 1 connectors 

must be used before 

SATA 2 and SATA 3.

Ensure SATA connectors are used in 

ascending order. For one device, use 

SATA 0. For two devices, use SATA 0 

and SATA 1. For three devices, use SATA 

0, SATA1, and SATA 2.

1797-SATA Drivelock is 

not supported in RAID 

mode.

Drivelock is enabled on 

one or more SATA hard 

drives, and they cannot 

be accessed while the 

system is configured for 

RAID mode.

Either remove the Drivelocked SATA 

device or disable the Drivelock feature. 

To disable the Drivelock feature, enter 

Computer Setup, change 

Storage 

> 

Storage Options 

> 

SATA 

Emulation 

to 

IDE

, and select 

File 

> 

Save Changes and Exit

. Reenter 

Computer Setup and select 

Security 

> 

Drivelock

. For each listed 

Drivelock-capable SATA device, ensure 

Drivelock is 

Disabled

. Lastly, change 

Storage 

> 

Storage Options 

> 

SATA Emulation 

back to 

RAID 

and 

select 

File 

> 

Save Changes and 

Exit

.

1801-Microcode Patch 

Error

Processor not supported 

by ROM BIOS.

1. Upgrade BIOS to proper version.

2. Change the processor.

2200-PMM Allocation 

Error during MEBx 

Download

Memory error during 

POST execution of the 

Management Engine 

(ME) BIOS Extensions 

option ROM

1. Reboot the computer.

2. Unplug the power cord, re-seat the 

memory modules, and reboot the 

computer.

3. If the memory configuration was 

recently changed, unplug the 

computer, restore the original 

memory configuration, and reboot 

the computer.

4. If the error persists, replace the 

system board.

POST Error Messages 

(Continued)

Screen Message

Probable Cause

Recommended Action

Summary of Contents for Compaq dx7300











































































































































































































































Reviews:

No comments

Related manuals for Compaq dx7300

Tandy WP-2 Service Manual preview
WP-2
Brand: Tandy Pages: 138
IBM 330 Type 6577 User Manual preview
330 Type 6577
Brand: IBM Pages: 102
Uplift Desk UDA100-clamp Instructions preview
UDA100-clamp
Brand: Uplift Desk Pages: 4
ASROCK DESKMINI SERIES User Manual preview
DESKMINI SERIES
Brand: ASROCK Pages: 70
JVC HC-7GB Instructions Manual preview
HC-7GB
Brand: JVC Pages: 57
NEC POWERMATE PROFESSIONAL 9000E - SERVICE Service Manual preview
POWERMATE PROFESSIONAL 9000E - SERVICE
Brand: NEC Pages: 206
NEC PowerMate ES SlimLine Series Specifications preview
PowerMate ES SlimLine Series
Brand: NEC Pages: 2
NEC POWERMATE P - SERVICE MANUAL 1995 Service And Reference Manual preview
POWERMATE P - SERVICE MANUAL 1995
Brand: NEC Pages: 171
NEC POWERMATE PRO2180 Manual preview
POWERMATE PRO2180
Brand: NEC Pages: 211
NEC POWERMATE P2166 Manual preview
POWERMATE P2166
Brand: NEC Pages: 221
NEC POWERMATE P ETC User Manual preview
POWERMATE P ETC
Brand: NEC Pages: 177
NEC POWERMATE P2166 Service Manual preview
POWERMATE P2166
Brand: NEC Pages: 219
NEC POWERMATE NETPC System Administrator Manual preview
POWERMATE NETPC
Brand: NEC Pages: 125
NEC POWERMATE PRO150 Manual preview
POWERMATE PRO150
Brand: NEC Pages: 167
NEC PowerMate Pro 2180 User Manual preview
PowerMate Pro 2180
Brand: NEC Pages: 211
NEC POWERMATE PROFESSIONAL 9000E - SERVICE User Manual preview
POWERMATE PROFESSIONAL 9000E - SERVICE
Brand: NEC Pages: 283
NEC POWERMATE PRO150 Service Manual preview
POWERMATE PRO150
Brand: NEC Pages: 167
NEC POWERMATE PROFESSIONAL 9000 - SERVICE Service Manual preview
POWERMATE PROFESSIONAL 9000 - SERVICE
Brand: NEC Pages: 296

Brands by name

Popular brands

Load more brands