background image

First Printing — January 1997

Copyright 1997

NEC Computer Systems Division

Packard Bell NEC, Inc.

1414 Massachusetts Avenue

Boxborough, MA   01719-2298

All Rights Reserved

PROPRIETARY NOTICE AND LIABILITY DISCLAIMER

The information disclosed in this document, including all designs and related materials, is
the valuable property of NEC Computer Systems Division, Packard Bell NEC, Inc.
(hereinafter “NECCSD”) and/or its licensors. NECCSD and/or its licensors, as appropriate,
reserve all patent, copyright and other proprietary rights to this document, including all de-
sign, manufacturing,reproduction, use, and sales rights thereto, except to the extent said
rights are expressly granted to others.

The NECCSD product(s) discussed in this document are warranted in accordance with the
terms of the Warranty Statement accompanying each product. However, actual
performance of each such product is dependent upon factors such as system configuration,
customer data, and operator control. Since implementation by customers of each product
may vary, the suitability of specific product configurations and applications must be
determined by the customer and is not warranted by NECCSD.

To allow for design and specification improvements, the information in this document is
subject to change at any time, without notice. Reproduction of this document or portions
thereof without prior written approval of NECCSD is prohibited.

NEC is a registered trademark of NEC Corporation and FastFacts, MultiSync, and PowerMate are either trademarks or registered trademarks

of NEC Technologies, Inc.; these trademarks are used under license by Packard Bell, NEC.

All other product, brand, or trade names used in this publication are the trademarks or registered trademarks of their respective trademark

owners.

Summary of Contents for POWERMATE P2166




























































































































































































































Reviews: